Guard/Guardian God Tier Request
NOTE: Trolls do not have the horned hood, since they already have natural horns and they would just look silly.
Feel free to use/modify. Credit if you do, thanks!
Check out my other designs HERE
Fullsize HERE
extra points to you if you know what video game villain inspired the hood ;0
Dame God Tier Request
Feel free to use/modify. Credit if you do, thanks!
Check out my other designs HERE
Fullsize HERE
hip hip hooray only two more to do until requests are open again
Poet God Tier Request
Feel free to use/modify. Credit if you do, thanks!
Check out my other designs HERE
Fullsize HERE
Some of you guys wanted me to post my Bro talk sprites. Here are most of them.
Your free to use them as long as credit is given
Spirograph Snowflakes (with 10 points)
Ok. For those of you unfamiliar with origami diagrams, dash-dash-dash lines mean valley fold (points away from you) and dash-dot-dash lines mean mountain fold (points towards you). For me, dot-dot-dot lines mean cutting.
For this you’ll need to start with a square of paper and have a pair of scissors, a protractor, and a pencil at the ready. The paper should be either very thin, or as I have it, very large; the ten-point spirograph requires more folds than the eight point.
1: Fold diagonally in half.
2: Fold into quarters as shown.
3: Rotate 45 degrees so that it appears as in the next picture.
4: Use your protractor to mark every 18 degrees as shown.
5: Starting from the open side, fold the top layer only along the marks, alternating between mountain and valley folds.
(It should look like an accordion after that)
6: Flip the whole model horizontally, so that the accordioned flap is on the bottom.
7: Fold the uncreased flap the same way, using the creased flap as a template to guide you.
(FULL ACCORDION! This shows the square unfolded to ½.)
8: Compress the accordion as shown in the next picture.
9: You will notice there are inner flaps. You have to cut off the top points, and where you cut should be determined by the innermost flap; try to cut just at the top of that shortest flap. (Flap is a very silly noun.) Also cut off the bottom points as shown.
10: Cut out a triangular section as shown.
11: Another, slightly smaller…
12: Again. In this step and the next cuts be sure to keep an eye on the back side of the model; the paper tends to creep during these cuts, and you could end up severing an important piece if you don’t watch out.
13: Another…
14: You know the drill. (Heheh it looks like a drill I’ll be quiet now)
15: Smaller cuts…
16: Even smaller…
17: OK UNFOLD NOW…
Bam! There it is! A beautiful ten-point spirograph, as seen in Homestuck. Tape them to the ceiling at your Homestuck christmas party! Use them as your tree-skirt!
Blow people’s minds! Put an eight-point spirograph in the middle! Find some green paper for the large one and make a horde of small red ones, tape ‘em together for a wreath! Show me what you do with them! Please! Thanks for reading!
!
Demon God Tier Request
NOTE: Trolls do not have the horned hood, since they already have natural horns and they would just look silly.
Feel free to use/modify, but please credit if you do.
Check out my other designs here
Fullsize here
haven’t seen anyone do this yet so… (and hope nobody minds if i tried…)
did a template of the canon Page design 8U (and used the background from that god tier sheet too lol)
took that hero mode of tavros (with missing legs dsjgdjg) from the flash… so i had to draw the legs >:T dgsdgdsgdfsdfhdfsjhfdjskhjdfshjdshk they look weird djgksdjgsdkjg
After seeing the custom tumblr home buttons floating around, I decided I really needed a Homestuck-themed post dash. And then I got carried away, as per usual. I obviously can’t use six different themes at once, so feel free to install the Stylish plugin and download away:
Aspects | Kids | Lowbloods | Highbloods
Bonus level: Lowbloods and Highbloods in Alternian, for those who enjoy not being able to read their post bars!
@JJ, here you go
